Question:
How can I customize the Forte’s sliders, buttons, wheels and pedals to control my DAW and/or virtual instruments?

Answer:

Getting the Forte’s physical controller to activate various features/parameters in your DAW requires two basic steps:

  1. In your DAW: define the necessary MIDI CC number needed to trigger the desired function;
  2. On the Forte: assign that same MIDI CC number to the chosen physical controller (slider, button, wheel, etc) you want to use to activate the given DAW/VI parameter.

This article will address step 2, assigning the various physical controllers on your Forte to transmit the needed DAW/VI MIDI values. For step 1, please refer to your specific DAW and/or VI documentation as to what MIDI CC’s it may use, or allow assignment of, for controlling its various features.

The Forte offers 40 assignable MIDI controllers in total, ranging from pedals, to sliders to buttons and the piano keys themselves. Each controller itself is further classified as either Switch type or Continuous type. A Switch (switch pedal, button or key) transmits two values (one for On and one for Off) and Continuous controllers (wheels, continuous pedals and sliders) transmit 128 values (0-127). In the table below Switch type controllers are labeled in black, Continuous controllers are in blue:

Wheels Pedals Sliders Buttons Keys
ModWheel Sw. Pedal 1 Slider A Variation Pressure
Pitch Wheel Up Sw. Pedal 2 Slider B Zone 1 Sw Key 1
Pitch Wheel Down Sw. Pedal 3 Slider C Zone 2 Sw Key 2
CC Pedal 1 Slider D Zone 3 Sw Key 3
CC Pedal 2 Slider E Zone 4 Sw Key 4
Slider F Switch 1 Key 5
Slider G Switch 2 Key 6
Slider H Switch 3 Key 7
Slider I Switch 4 Key 8
Switch 5 Key 9
Key 10
Key 11
Key 12

 

Tip: Before beginning, it is strongly suggested you develop a list of those parameters/functions in your DAW or VI’s that you want to control along with the designated MIDI CC number for each. Then determine what Forte controllers (from the above table) you want triggering each DAW/VI function. With this plan in hand, you can then simply go one by one, assigning each as needed.

Below we will construct a custom Forte Multi template to house your custom DAW/VI controller assignments.

1. Go to Multi mode and select Multi 255 “Forte Control” as a starting point:
2. Press EDIT, and on the OVERVIEW page set the Program for Zone 1 to “0 None”:
3. Following, select the MAIN page and set the Destination to “USB” or “MIDI” (depending on your physical cable connections to your computer), and set EntryProgChng to “Off”:

4. Next, select the CONTROLS page. This page is where all of the physical controller assignments will get defined:

Select the desired physical control by either:

a) scrolling through the “Controller” list at the top of the screen to locate the desired controller, or

b) use Intuitive Entry to quickly jump to the desired controller (note this works for all controllers except the 12 key triggers). To use Intuitive Entry, select the Controller field, press+hold the keypad ENTER button while you move/activate the desired controller. This will auto-select the given controller.

Switch and Continuous controllers have slightly different programming parameters. We’ll look at each individually here:

-Continuous Controller-

      1. Set the Mode parameter to “MIDI CC”
      2. Set the Destination field to the MIDI CC # needed to trigger the chosen parameter in your DAW/VI. For example here we assigned MIDI 12.
      3. Set Scale to “100%”.
      4. Set Add to “0”.
      5. Set Curve to “Linear”
      6. Set Entry Position and Exit Value both to “None”.

Note: These are the basics. In the Advanced Tips section below we’ll look at some creative uses of Scale/Add/Curve.

-Switch Controller-

    1. Set the Mode parameter to “MIDI CC”
    2. Set the Type to either “Momentary” or “Toggled”. Momentary is generally used for press+hold applications where the function assigned is only applied while the switch is depressed (ex, sustain pedal). Toggled is good for control over on/off type features, requiring you press the switch once to enable the designated function and a second press to disable it.
    3. Set the Destination field to the MIDI CC # needed to trigger the chosen parameter in your DAW/VI. For example here we assigned MIDI 80.
    4. Set the On Value to “127” (or other value if needed by your DAW/VI (this is the value sent when the switch is first pressed).
    5. Set the Off Value to “0” (or other value if needed by your DAW/VI (this is the value sent when the switch is either released (momentary) or pressed a second time (toggled).
    6. Set Entry State and Exit State both to “None”.

Test each controller as you assign it, double checking it activates the desired function in your DAW/VI.

5. Go back to Step 4a/b and repeat for each physical controller-to-parameter pairing you wish to make.

6. When done, it is advisable that you scroll through all of the Forte’s controllers and disable any you know you are NOT using that may have been enabled by default in this template. To disable any controller simply set its Mode field to “Off”.

7. Press SAVE and name the Multi when finished. Now whenever you are working with your DAW/VI’s, select this Multi.

ADVANCED TIPS

Continuous Controller Scaling

Does that fader, knob or CC pedal not trigger the chosen parameter smoothly enough? Need it to operate over a narrower range? in reverse? Continuous controllers offer 3 additional parameters that can be used to tailor their output to perform in a variety of useful ways:

“Scale”: Reduce or increase the output range, expressed as a percentage. Values lower than 100% decrease the range; values greater than 100% increase it.

“Add”: Uniformly add or subtract a fixed amount to the output (+/-127). This effectively acts as an offset.

“Curve”: Select from 9 different shapes ranging from Linear, Compressed, Expanded, Reversed, etc..

Velocity Scaling

Need to increase or decrease the key velocity (ie sensitivity)? Similar to the above you can tweak the velocity output in a number of ways to best marry with the VI and specific program or passage you may be playing. On the MAIN page there are four Velocity adjustment parameters that serve this purpose:

“Velocity Mode”: Choose between “Traditional” (which reveals the following 3 additional parameters) or “Fixed”, the later allowing you to specify a singular/fixed velocity value ranging from 0-127.

“Velocity Scale”: Reduce or increase the output range, expressed as a percentage. Values lower than 100% decrease the dynamic range; values greater than 100% increase it.

“Velocity Offset”: Uniformly add or subtract a fixed amount to the output (+/-127).

“Velocity Curve”: Select from 9 different dynamic shapes ranging from Linear, Compressed, Expanded, Reversed, etc..

Multiple Multis

Want more faders/knobs/buttons? Or maybe need a separate set of controls for each VI you use? Use multiple Multis, each purpose built with its own customized CC assignments tailored to a given DAW window, VI or performance style. Store each of these as a Favorite and easily switch between these task-specific Multi templates on the fly.

Performance Arps

Need a fast string ostinato? synth pattern? or maybe a harp glissando? Create a specific Multi that uses the Forte’s Arps to enhance your performance.

Key Triggers

Key Triggers (1-12) are switch controllers designed to act as either a simple switch OR to allow you to play chords from a single key. When setting the “Mode” to Chord, added parameters appear on screen allowing you to designate the trigger “Key” along with settings for building a chord of up to 8 notes. This facilitates playing larger chords with ease. This same approach can also be used to create epic drum/percussion hits triggering up to 8 of your favorite VI drum hits simultaneously, each with its own velocity setting for creating the perfect balance.