Question:
How can I adjust the instruments touch sensitivity?

Answer:

(manual ref. see “MIDI / Entering MIDI Edit Mode”.)

To set the keyboard’s “Keyboard Touch” parameter:

1. 1. Press and hold down the MIDI button.

1. While depressing the MIDI button, per the diagram below, strike a piano note from C#1 to D#2 to select one of the Touch Maps, 1-7:

Map 1 has the greatest dynamic range (allows for harder/heavier playing style). Map 7 has the least dynamic range (allows for easier/lighter playing style). The default selection is Map 4.

The Keyboard Touch setting is retained when the power is off.

Question:
How can I adjust the instruments touch sensitivity?

Answer:

(manual ref. see “MIDI / Entering MIDI Edit Mode”.)

To set the keyboard’s “Keyboard Touch” parameter:

1. 1. Press and hold down the MIDI button.

1. While depressing the MIDI button, per the diagram below, strike a piano note from C#1 to D#2 to select one of the Touch Maps, 1-7:

Map 1 has the greatest dynamic range (allows for harder/heavier playing style). Map 7 has the least dynamic range (allows for easier/lighter playing style). The default selection is Map 4.

The Keyboard Touch setting is retained when the power is off.

Question:
I’m trying to a record or load a song in my Mark 6/8/10/110/150 and I get error “E18” (Memory Full).

Answer:

Once the memory is FULL existing songs must be deleted in order to make more room.

You have two options on how to proceed:

1. you can delete all existing songs, whereby freeing up all memory to start over…OR
2. you can delete select songs, leaving some in memory while erasing others.

!!IMPORTANT!! With either method it is recommended you save to floppy disk any custom songs currently in memory that you want to keep before you proceed !! – please see the manual for details on saving to floppy.

On pg. 44-45 of the manual, both of the above methods for clearing space are detailed under the “MIDI Edit” section.

To clear (or reset as it’s called) the entire memory…., simply hold MIDI and press the highest note on the keyboard simultaneously and ALL of the unit’s memory will be cleared and its settings returned to their factory default. Described as “Reset Parameters” in the manual.

To delete an individual song… press MIDI and the highest ‘F’ natural on the keyboard (described as Delete Song/Style in the manual). At this point all filled song location buttons on the front panel will begin to blink indicating which song slots are occupied. From here press the ONE song you wish to erase and in the screen you will be prompted with a “Y” or “N” confirming YES or NO you want to proceed (or not). Press the appropriate arrow button beneath the display to continue

Question:
How can I restore my Mark 10/Mark 110/Mark 150 to its factory defaults?

Answer:

There are two methods:

Method 1:

1. Turn the unit on
2. Hold the MIDI button and strike the top note on the keyboard (C8) at the same time.

The unit is now reset.

If the unit won’t come up and permit method 1…

Method 2:

1. Turn the unit off
2. With the right hand, press and hold the “Jazz/Swing Waltz” and “Start/Stop” buttons located to the right and down from the numeric display
3. Turn the unit on, and with your left hand, immediately press and hold the Track 1 Button, located in the upper left panel area
4. Wait 5 seconds then release all 3 buttons
5. All panel LEDs should flash, then the numeric display should display [.0.0.0] and the three reverb LEDs, Room, Stage, Hall, should be on.
   This is Diagnostic Menu Display
6. Press and release the Warm/Bright button located adjacent to the Reverb LEDs.
   The Display should display numbers indicating the specific test being performed.
7. When test number seven (7), panel LED test, is performing you may Turn Off Power, wait a few seconds, then Turn On Power again.

The unit is now reset.

Question:
How can I convert one of my Kurzweil Song files into an audio CD?

(aka converting .SNG, or .MID files into .WAV, .AIF, .MP3 audio files)

Answer:

First, you need to remember that when you are recording a song in the Kurzweil, you are not recording audio, you are recording MIDI information.

It is important to understand that MIDI data is not audio and by itself makes no sound. All MIDI consists of is remote control performance data – a record of what keys you played, pedals you pressed, and so on. When the MIDI information is sent back to the instrument, it is the sound module part of the instrument that then creates the sound. So the short answer is there is no way to directly convert MIDI data into audio.

Therefore, in order to make an audio CD (or mp3), you are going to have to make a digital audio recording of the Kurzweil’s audio output while it is playing the song. This means recording into some type of external digital audio recorder.

One such example might be to record directly to a stand-alone CD Audio Recorder. Another possibility would be to use digital audio recording software and a good quality audio recording card for your computer. With either you would connect the Kurzweil to the audio inputs of your chosen recording device or audio interface, start playing the song on your Kurzweil, and record just as you would if you were recording to a traditional tape recorder. If recording to a dedicated CD Recorder, your job is basically done. If recording into a computer, once the audio is digitized (recorded), you can then use CD writing software to burn a CD with the audio files and /or create mp3’s.

Question:
I’m trying to a record or load a song in my Mark 6/8/10/110/150 and I get error “E18” (Memory Full).

Answer:

Once the memory is FULL existing songs must be deleted in order to make more room.

You have two options on how to proceed:

1. you can delete all existing songs, whereby freeing up all memory to start over…OR
2. you can delete select songs, leaving some in memory while erasing others.

!!IMPORTANT!! With either method it is recommended you save to floppy disk any custom songs currently in memory that you want to keep before you proceed !! – please see the manual for details on saving to floppy.

On pg. 44-45 of the manual, both of the above methods for clearing space are detailed under the “MIDI Edit” section.

To clear (or reset as it’s called) the entire memory…., simply hold MIDI and press the highest note on the keyboard simultaneously and ALL of the unit’s memory will be cleared and its settings returned to their factory default. Described as “Reset Parameters” in the manual.

To delete an individual song… press MIDI and the highest ‘F’ natural on the keyboard (described as Delete Song/Style in the manual). At this point all filled song location buttons on the front panel will begin to blink indicating which song slots are occupied. From here press the ONE song you wish to erase and in the screen you will be prompted with a “Y” or “N” confirming YES or NO you want to proceed (or not). Press the appropriate arrow button beneath the display to continue

Question:
How can I load Mark 6/8/10/110 songs into another sequencer or instrument?

Answer:

The Mark 6, 8, 10, 110, and 150 save songs in our own .SNG format, which cannot be read by other sequencers. These models do not have the ability to export songs in the .MID format. However, we have designed a PC program called “EXPORT” which will convert .SNG files to .MID format.

EXPORT is available in both Windows and DOS versions. (Operating instructions are found within each download).

Please realize these apps were created in the mid-90’s (i.e. Win 95/98 era). As such they have not been tested with later Windows OS’s. If you have problems with the Windows version, you can download a DOS version, which seems to work for just about everyone.

For Mac users, sorry, but we do not have a Mac version. However, you can still get the song into an external sequencer by recording from one sequencer to another in real time.

To do this:

1. Connect the Mark MIDI OUT to the MIDI IN of your computer MIDI Interface OR external hardware sequencer
2. Set the Kurzweil to Transmit Sequence Data by holding the MIDI Button and striking G#5 on the keyboard (as shown on page 45 of the manual)
3. On the external sequencer, set it to sync to an External Clock
4. Set up the tracks on the external sequencer to match all the channels being used on the Kurzweil sequence and make sure it is set to Multi-Record. (This will allow you to record multiple channels of information in one pass. If the sequencer can’t do this, you will have to make one pass for each MIDI channel.)
5. In the Kurzweil recorder select the song as needed
6. Press Record on the external sequencer
7. Press play on the Kurzweil

The data will be recorded in real time.

Question:
How can I load songs off disk for playback in my MK10/110/150?

Answer:

NOTE: all references to the “Mark 10” (MK10) refer equally to the Mark 10, Mark 110 and Mark 150 models.

1. Insert disk
2. Press Load Songs – display will show “ALL”
3. From here you have two options:

1. 1. Load up to the first 8 songs in order off the disk.

OR

1. Load individual songs off the disk one at a time.

a. To Load the first 8 (ALL), when you see “ALL” in screen, press any of the flashing Song buttons on you left. The MK10 will then attempt to load as much as it can (memory permitting) up to the first 8 songs off the disk.

To load BEYOND the first 8 songs AND/OR to load individually, you need to scroll up the list one selection at a time using the UP arrow key beneath the display.

Once you have selected on screen the ONE song to load next, press a blinking Song button (indicating its empty) on your left to load INTO.

Question:
How can I convert one of my Kurzweil Song files into an audio CD?

(aka converting .SNG, or .MID files into .WAV, .AIF, .MP3 audio files)

Answer:

First, you need to remember that when you are recording a song in the Kurzweil, you are not recording audio, you are recording MIDI information.

It is important to understand that MIDI data is not audio and by itself makes no sound. All MIDI consists of is remote control performance data – a record of what keys you played, pedals you pressed, and so on. When the MIDI information is sent back to the instrument, it is the sound module part of the instrument that then creates the sound. So the short answer is there is no way to directly convert MIDI data into audio.

Therefore, in order to make an audio CD (or mp3), you are going to have to make a digital audio recording of the Kurzweil’s audio output while it is playing the song. This means recording into some type of external digital audio recorder.

One such example might be to record directly to a stand-alone CD Audio Recorder. Another possibility would be to use digital audio recording software and a good quality audio recording card for your computer. With either you would connect the Kurzweil to the audio inputs of your chosen recording device or audio interface, start playing the song on your Kurzweil, and record just as you would if you were recording to a traditional tape recorder. If recording to a dedicated CD Recorder, your job is basically done. If recording into a computer, once the audio is digitized (recorded), you can then use CD writing software to burn a CD with the audio files and /or create mp3’s.

Question:
I’m trying to a record or load a song in my Mark 6/8/10/110/150 and I get error “E18” (Memory Full).

Answer:

Once the memory is FULL existing songs must be deleted in order to make more room.

You have two options on how to proceed:

1. you can delete all existing songs, whereby freeing up all memory to start over…OR
2. you can delete select songs, leaving some in memory while erasing others.

!!IMPORTANT!! With either method it is recommended you save to floppy disk any custom songs currently in memory that you want to keep before you proceed !! – please see the manual for details on saving to floppy.

On pg. 44-45 of the manual, both of the above methods for clearing space are detailed under the “MIDI Edit” section.

To clear (or reset as it’s called) the entire memory…., simply hold MIDI and press the highest note on the keyboard simultaneously and ALL of the unit’s memory will be cleared and its settings returned to their factory default. Described as “Reset Parameters” in the manual.

To delete an individual song… press MIDI and the highest ‘F’ natural on the keyboard (described as Delete Song/Style in the manual). At this point all filled song location buttons on the front panel will begin to blink indicating which song slots are occupied. From here press the ONE song you wish to erase and in the screen you will be prompted with a “Y” or “N” confirming YES or NO you want to proceed (or not). Press the appropriate arrow button beneath the display to continue

Question:
How do I erase an individual track in the Mark 6/8/10/110/150?

Answer:

To erase a recorder Track, simply record “nothing” over it:

1. press Record (the record button will blink)
2. select the track to be erased (its button will blink)
3. press Play/Pause (allow the recorder to play over the area to erase – do not play any notes or touch any controllers while recording)
4. press Stop

Question:
How can I load Mark 6/8/10/110 songs into another sequencer or instrument?

Answer:

The Mark 6, 8, 10, 110, and 150 save songs in our own .SNG format, which cannot be read by other sequencers. These models do not have the ability to export songs in the .MID format. However, we have designed a PC program called “EXPORT” which will convert .SNG files to .MID format.

EXPORT is available in both Windows and DOS versions. (Operating instructions are found within each download).

Please realize these apps were created in the mid-90’s (i.e. Win 95/98 era). As such they have not been tested with later Windows OS’s. If you have problems with the Windows version, you can download a DOS version, which seems to work for just about everyone.

For Mac users, sorry, but we do not have a Mac version. However, you can still get the song into an external sequencer by recording from one sequencer to another in real time.

To do this:

1. Connect the Mark MIDI OUT to the MIDI IN of your computer MIDI Interface OR external hardware sequencer
2. Set the Kurzweil to Transmit Sequence Data by holding the MIDI Button and striking G#5 on the keyboard (as shown on page 45 of the manual)
3. On the external sequencer, set it to sync to an External Clock
4. Set up the tracks on the external sequencer to match all the channels being used on the Kurzweil sequence and make sure it is set to Multi-Record. (This will allow you to record multiple channels of information in one pass. If the sequencer can’t do this, you will have to make one pass for each MIDI channel.)
5. In the Kurzweil recorder select the song as needed
6. Press Record on the external sequencer
7. Press play on the Kurzweil

The data will be recorded in real time.

Question:
How can I load songs off disk for playback in my MK10/110/150?

Answer:

NOTE: all references to the “Mark 10” (MK10) refer equally to the Mark 10, Mark 110 and Mark 150 models.

1. Insert disk
2. Press Load Songs – display will show “ALL”
3. From here you have two options:

1. 1. Load up to the first 8 songs in order off the disk.

OR

1. Load individual songs off the disk one at a time.

a. To Load the first 8 (ALL), when you see “ALL” in screen, press any of the flashing Song buttons on you left. The MK10 will then attempt to load as much as it can (memory permitting) up to the first 8 songs off the disk.

To load BEYOND the first 8 songs AND/OR to load individually, you need to scroll up the list one selection at a time using the UP arrow key beneath the display.

Once you have selected on screen the ONE song to load next, press a blinking Song button (indicating its empty) on your left to load INTO.

Question:
I am playing a .MID file which I loaded off disk. It plays the right notes but not using the correct sounds. How can I fix this?

Answer:

Most Standard MIDI Files (.MID) are intended for an instrument with General MIDI (GM) compatibility. The Mark 6/8/10/110/150 is GM compatible but it must be turned On in order to put the Mark into a special GM mode and hear the intended GM sounds. Many .MID files will have an embedded sys-ex message to turn GM “On” automatically. But if the sequence does not contain this message, you need to turn it on manually (if you are reading this tutorial, the latter likely applies to you).

To do this:

Press and hold the MIDI button, simultaneously striking the lowest black note (Bb0) on the keyboard (as shown under the MIDI EDIT sections of your manual). You can tell when GM is turned On when you see a dot (decimal point) after the last character in the display. Once enabled, GM material will playback correctly.

Question:
How can I get all loaded songs to playback continuously in a loop?

Answer:

This is accomplished by using “Chain Play” mode:

1. Record and/or load from disk the songs you want played in a chain (up to 8 max)
2. Press and hold the ‘Demo’ button and then, at the same time, press ‘Loop’

In doing so, Song 1 will begin to play, followed automatically by Song 2, and so on. When the last Song is finished, the playback chain will start over again at Song 1. You can exit Chain Play mode by pressing any front panel button.

(see “Chain Play” in the Index of the User’s Manual for more detail).